Beetle Kill Blue Stain Pine

Home Lumber and Building Materials Beetle Kill Blue Stain Pine
Beetle Kill Blue Stain Pine 2017-09-28T21:08:15+00:00

Front Range Lumber is Denver’s Beetle Kill Blue Stain Pine headquarters.

Beetle Kill Pine and Blue Stain Pine are the same item. A fungus carried by the pine beetle infects and eventually kills the tree, a side effect of this fungus is the “blue” discoloration in varying amounts in the wood.

Blue Stain / Beetle Kill Pine

Beetle kill pine or blue stain boards are available in 1×6 tongue and groove in 8′ through 16′ lengths. What isn’t so common are 1×4 through 1×12 “square” edge boards. More spottily, blue stain lumber comes in 2×4 through 2×8 dimensional sizes. Front Range Lumber stocks all these sizes. See our Size Availablility Chart below.

Beetle Kill Blue Stain Pine misconceptions.

Blue Stain Pine is a very misunderstood product. There are three major misconceptions about Beetle Kill Blue Stain Pine:

  • It all comes from very close to Denver (or Colorado)
  • Every board is very blue
  • Every board will be totally useable in its entirety

Important: The pictures on this page are meant to be illustrative only and are NOT meant to indicate overall quality, ANY amount of blueness or other natural characteristics, all of which vary. Wood in general and in this case, beetle kill blue stain pine, differs in appearance between boards, batches and seasons.

Beetle Kill Blue Stain Pine PhotoThese photos show the huge variation in color (including amount and shades of blueness) found in this product. All three show other characteristics commonly found in this somewhat rustic item – cracking, knots, pitch pockets, etc. In fact the 1×4 sample of  beetle kill pine lumber on the far right has beetle-boring holes which is sometimes found in the material – Don’t Worry – this wood has been heat treated/kiln dried and that process kills any living insects in the wood. These photos also show the 3 major “patterns” Front Range Lumber stocks: Regular boards like on the left and right, a T&G V-groove pattern (2nd sample) and a square edge T&G pattern (3rd sample).

  • Blue stain and beetle kill are the same item. A fungus carried by the pine beetle infects and eventually kills the tree, a side effect of this fungus is the “blue” discoloration in varying amounts in the wood. A typical log that produces blue stain boards is only “blue-colored” in the outer-most 2″ or so of the tree. The beetles/fungus affect only the sapwood portion of the tree.
  • While 1×6 T&G boards used for paneling and siding are the most common item available in blue stain pine, many other sizes are readily available, including boards in 1×4 through 1×12 widths in 8′ through 16′ lengths and 2×4 through 2×12 widths, again in 8′ through 16′ lengths.
  • The blue staining of the wood does NOT reduce the strength or integrity of the wood itself.
  • All blue stain wood is graded as #3 grade. The grading rules for #2 (or better grade) boards do not allow for any blue stain to be showing, which means that all blue stain is assessed as #3. However, looking at the boards, the overwhelming majority of the goods you’ll receive are far better than the “average” #3 board, which is generally a low grade meant for palleting, crating, very rough construction or bracing. However, there WILL be lower quality boards in the mix, please plan to have some “waste” as you may be unable to use a small portion of the wood you purchase due to large knots, wane, or other undesirable aspects in any given board. Based on its low cost, you can still have a very economical product. Some percentage of the boards will have undesirable defects. On a milled product such as 1×6 T&G paneling, the percentage will fall off further since machining will take off some of the defects.
  • Be aware of the wide variation in the boards in both “blueness” and overall quality/appearance.
  • It is important to note the amount of “blueness” varies wildly from board to board. As stated earlier, ANY amount of blue in the board necessitates a #3 grade.
  • This is a true pine board. Most pine (i.e., non-blue stain) is labeled as pine but is truly a mix of pine and spruce species. Spruce as a whole is a less desirable wood as the knot structure lends itself to a less attractive wood surface.
  • This material can readily be machined into log siding, 2x decking products, any siding pattern desired and moldings. Many users are interested in doors, trim and flooring – all possible in this type of wood.
  • Blue stain is often talked about as a “green” product, especially as many believe it is locally sourced, thereby reducing carbon footprints and the like. However, this is an incorrect assumption despite significant stands of beetle kill lumber in Colorado (even in the immediate I-70 mountain corridor). Virtually all blue stain being sold in our area comes from Canada, the Dakotas, Montana and Idaho. One of the largest reasons for this sourcing is that there is no large commercial lumber mill operating within Colorado.
  • Many customers desire 1×6 tongue and groove boards to be used for flooring; for this application you’ll need to use square edge tongue and groove boards. This installation will leave no gaps between boards if installed properly resulting in a solid floor surface. One note of caution: pine is a softwood, unlike oak, maple, cherry, etc; therefore it may not perform as well in a flooring application.
  • Blue stain veneers are now available for plywoods. We stock 4×8 sheets in a 1⁄4″, 1⁄2″ and 3⁄4″ thickness. These are “good” both sides and generally come with an MDF core.

We can get blue stain boards machined into whatever pattern you’d like. For example, we ordered some “channel rustic” shiplap pattern for a customer recently – they were beautiful.

Blue stain plywood is now available in ¼”, ½” and ¾” thicknesses.

Download more information:

FileFile size
pdf Additional Information on Blue Stain Pine177 KB
Lengths
Sizes8'10'12'14'16'
1x4
1x6
1x8
1x12
2x4
2x6
1x6 T&G SQ.
1x6 T&G V
NOTE: We stock both V-groove (paneling, siding, etc) and square edge (generally flooring) in 1×6 tongue and groove.

Hours

Monday-Friday: 7-5
Saturday: 8-1
Closed Sunday

Enter Our Contest!

Enter our Proud of My Project Contest for a chance to WIN a $100 store credit.

$50 Delivery!

We keep our delivery charges low for you!

Join Our Email List!

FRL Featured on TV!

Front Range Lumber has been featured on local TV.